Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Bergamid™ B70 VN4805 LS PM-Z BK - PA6 - Avient Corporation

Material Data Center offers the following functions for Bergamid™ B70 VN4805 LS PM-Z BK:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bergamid B datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 2.0 / * % ISO 294-4, 2577
Propiedades mecánicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 2000 / 1050 MPa ISO 527
Esfuerzo de fluencia 43 / 28 MPa ISO 527
Alarg. en límite elástico 3 / 4 % ISO 527
Alargamiento a rotura >50 / >50 % ISO 527
Módulo de flexión, 23°C 1200 / 450 MPa ISO 178
Resistencia al impacto Charpy, +23°C N / N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C N / N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 89 / 93 kJ/m² ISO 179/1eA
Propiedades térmicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Temp. reblandecimiento Vicat, B 165 / * °C ISO 306
ASTM Data
Combustibilidad UL 94 HB - UL 94
Espesores de probeta 3.2 mm -
Propiedades eléctricasSeco / CondUnidadesMétodo de ensayo
ASTM Data
Resistividad superficial * / 1E15 Ohm ASTM D 257
Resistividad volumétrica 1E15 / 1E15 Ohm*cm ASTM D 257
Otras propiedadesSeco / CondUnidadesMétodo de ensayo
Densidad 1070 / 1070 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 60 °C -
Tiempo de pre-secado 4 h -
Temperatura de la masa 240 - 260 °C -
Temperatura del molde 60 - 80 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola
Características especiales
Alto impacto o modificado al impacto
Características
Imprimible por láser
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.